Flat pack trailer kit, walls on, etc. we have paint

General Discussion about almost anything Teardrop or camping related

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby twisted lines » Fri Nov 20, 2020 10:35 am

Really nice :thumbsup:
5.5 X 10 Flatback Benroy in a pile,
And it's growing!
User avatar
twisted lines
The 300 Club
 
Posts: 386
Images: 2
Joined: Wed Oct 10, 2018 4:37 am
Location: Jefferson

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby saltydawg » Fri Nov 20, 2020 2:34 pm

twisted lines wrote:Really nice :thumbsup:


Thanks Twisted.

I know I am flooding the thread with pics, but I dont really have a build thread. And while building the box part has been covered here and other places many times, the stuff like the roof is not real common, nor the things like the little 120 volt fan is not commonly done either.

After feeling how warm my charger gets and knowing how much heat an inverter can put out the 20 bucks or so for the little fan makes sense, esp sense my trailer is basically solid foam and well insulated heat build up can be a real thing.

Besides, I feel showing all the little stuff may help someone else who is thinking about building one have a better idea of what they are getting in to and less likely to get discouraged. Granted in 3 months I have come from nothing to where I am now so I make it seem fast. My real trick to getting it done, is I will make sure I do an hour a day, even if it just measuring out the kitchen slide out.
Scott
Lost in Maryland
saltydawg
The 300 Club
 
Posts: 311
Joined: Tue Apr 24, 2012 8:34 pm
Location: Maryland

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby saltydawg » Fri Nov 20, 2020 8:28 pm

Okay kitchen drawer all built just need to wrap it in aluminum and cut the sink out, which I have not ordered yet.

And I did a quick clean up on the inside for an over all pic of the inside.

Image
Image
Scott
Lost in Maryland
saltydawg
The 300 Club
 
Posts: 311
Joined: Tue Apr 24, 2012 8:34 pm
Location: Maryland
Top

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby Greg M » Fri Nov 20, 2020 9:19 pm

You’ve just got to ask yourself “If I do the aluminum, will I feel like I cheaped out later?” If you don’t think so, then go for it.
Give a person a fish and you feed them for a day; teach a person to use the Internet and they won't bother you for weeks.
User avatar
Greg M
*Geek Extraordinaire
 
Posts: 1111
Images: 85
Joined: Mon Sep 12, 2005 12:40 am
Location: Victoria, BC, Canada
Top

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby saltydawg » Fri Nov 20, 2020 10:40 pm

Greg M wrote:You’ve just got to ask yourself “If I do the aluminum, will I feel like I cheaped out later?” If you don’t think so, then go for it.


I CANT HEAR YOU...MMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMM

I already did aluminum around the rear hatch sense it lifts as well and I wanted to protect it, and doing the edge of a 1 inch thick panel was a lot harder than just a corner.
Scott
Lost in Maryland
saltydawg
The 300 Club
 
Posts: 311
Joined: Tue Apr 24, 2012 8:34 pm
Location: Maryland
Top

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby saywhatthat » Tue Nov 24, 2020 8:19 pm

Think of using a flat panel like you have used . When you glued them together and faired out the joints . Dose it stand out much? When ever I did joints like you have. I have ground out a tapper . But doing it your way would save a bit of time and mess.
Just finish a full rebuild of a kit trailer. So used the kit sidewalls with a lot of rot to make a Temple.
So if I did not have grind out a taper that be great . just thinking about looks . What are your feeling on the look.
Il suffit de le faire
D.I.Y Light weight sleeper using D.I.Y rail top components.
viewtopic.php?f=50&t=66751
Build 4.5 by 8' using Trailtop fiberglass Components
http://tnttt.com/viewtopic.php?f=50&t=70729
User avatar
saywhatthat
Teardrop Master
 
Posts: 274
Images: 139
Joined: Sat Jun 11, 2016 3:31 am
Top

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby saltydawg » Tue Nov 24, 2020 8:50 pm

saywhatthat wrote:Think of using a flat panel like you have used . When you glued them together and faired out the joints . Dose it stand out much? When ever I did joints like you have. I have ground out a tapper . But doing it your way would save a bit of time and mess.
Just finish a full rebuild of a kit trailer. So used the kit sidewalls with a lot of rot to make a Temple.
So if I did not have grind out a taper that be great . just thinking about looks . What are your feeling on the look.


i sanded the corners with 60 grit sand paper on a da sander. I think I went about half way thru the gel coat.

The tape was only about a 1 inch overlap on each side, and i faired it out about 3 inches or so. You really cant tell it built up at all. And i love the "seamless" look.
Scott
Lost in Maryland
saltydawg
The 300 Club
 
Posts: 311
Joined: Tue Apr 24, 2012 8:34 pm
Location: Maryland
Top

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby saltydawg » Tue Nov 24, 2020 9:13 pm

Okay only very minor updates.

Sink, faucet, water tank, water heater ( went with instant ), and water pump ordered. I installed the track for the led tape light inside so no more looking like xmas lights. I also wired in the shore power plug, wired the inside 120 volt plugs, and cut in and wired the external speakers. The placement of the speakers is not the greatest, they are right in front and behind the wheel wells, not really far enough apart. But there was not anywhere I could put them that worked with whats inside and would look balanced outside, but I am not going for concert quality sound outside. The speakers are cheap pyle weather proof 4 inch speakers, so nothing fancy, the interior are much nicer 4" jbl speakers. Turns out the radio I bought has the ability to bridge out the rear speaker channel and an internal crossover to make the rear a subwoofer output. I might install an 8 inch sub for a little more bass

I have decent weather on friday and the day off so I am hoping for the first coat of paint. I will finish sanding and touching up anything I need to with filler on thursday.

Image
Image
Scott
Lost in Maryland
saltydawg
The 300 Club
 
Posts: 311
Joined: Tue Apr 24, 2012 8:34 pm
Location: Maryland
Top

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby twisted lines » Wed Nov 25, 2020 6:04 pm

Phone dims the light's ? Nice 8)
5.5 X 10 Flatback Benroy in a pile,
And it's growing!
User avatar
twisted lines
The 300 Club
 
Posts: 386
Images: 2
Joined: Wed Oct 10, 2018 4:37 am
Location: Jefferson
Top

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby twisted lines » Wed Nov 25, 2020 6:09 pm

I do appreciate the time you spend sharing!
5.5 X 10 Flatback Benroy in a pile,
And it's growing!
User avatar
twisted lines
The 300 Club
 
Posts: 386
Images: 2
Joined: Wed Oct 10, 2018 4:37 am
Location: Jefferson
Top

Re: Flat pack trailer kit, walls on, etc. Started the kitche

Postby saltydawg » Sun Nov 29, 2020 1:28 pm

We have some paint,first coat of white up high, and gray down low. I will will need to make the sticker that covers the joint between the white and gray, it will be black and varied in width to give some 3d look.

The gray goes on much better, I will have to sand the white and am buying a spray gun to do the second coat.

Oh and we have water, 25 gallons of it, probably be running the water lines this week. I have the fill and vent line done and the water pump mounted. I need to buy a weather proof box for the water heater since I went to an instant. I also put the water tank under the front of the bed, because I am going to put a small gray water tank under the trailer and that will allow the tongue weight not to change a whole lot. I can also use the water tank to adjust the tongue weight for driving on highways, and just fill when I get to the area of the final destination.

Image
Image
Image
Scott
Lost in Maryland
saltydawg
The 300 Club
 
Posts: 311
Joined: Tue Apr 24, 2012 8:34 pm
Location: Maryland
Top

Previous

Return to General Discussion

Who is online

Users browsing this forum: No registered users and 9 guests