Joining Plywood

Anything to do with mechanical, construction etc

Joining Plywood

Postby Frosteez » Sat Aug 02, 2008 12:40 pm

I am deciding the best way to join plywood. We need 4x9 3/4" Oak for the sides of a 5x9 Benroy> Can I biscuit join it? It will be single wall w/no insulation. Or is there a better way? All I can find from our supplier is 4x8 sheets. Thanks
Frosteez
Teardrop Builder
 
Posts: 36
Joined: Tue Jul 22, 2008 9:54 pm
Location: Chico, Ca.

Postby Sparksalot » Sat Aug 02, 2008 12:44 pm

Have you tried wood working specialty stores as a source? I was able to get
4x10 red oak that way. They needed 2 days notice, but got it no problem.
Holy cow, Rose is a teenager now! Done? Surely you jest. A teardrop is never "done".

The Compass Rose build thread: viewtopic.php?t=23213

Inspiration: http://tnttt.com/Design_Library/Trailer%20for%20Two.htm

It's got a cop motor, a 5.3 LS plant, it's got cop tires, cop suspensions, cop shocks. ~ Elwood Blues
User avatar
Sparksalot
Silver Donating Member
 
Posts: 1624
Images: 682
Joined: Fri Feb 15, 2008 9:36 pm
Location: Texas by God

Postby Steve_Cox » Sat Aug 02, 2008 1:06 pm

When joining plywood there is the best way, then there are the easier ways, one of the easy ways is good enough for a teardrop. If you were building a boat the best way is an 8 to 1 scarf joint. Teardrops can use splines, biscuits, or a butt splice with a backing board just to name 3. Unless you are one of the router gurus here, one of those three would probably suffice.
Steve
User avatar
Steve_Cox
4000 Club
4000 Club
 
Posts: 4903
Images: 196
Joined: Sun Apr 03, 2005 8:46 am
Location: Albuquerque New Mexico
Top

Postby len19070 » Sat Aug 02, 2008 2:02 pm

I like splining plywood to join it.

Image

I've made some pretty big sheets of plywood.

Image

Happy Trails

Len
:peace: :peace: :peace: :peace: :peace:
http://s26.photobucket.com/user/len1907 ... 20trailers

"If you do good things, good things will happen to you"..... Earl Hickey
User avatar
len19070
3000 Club
3000 Club
 
Posts: 3054
Images: 24
Joined: Tue Aug 17, 2004 7:44 pm
Location: S.E Pa. Morton
Top

Postby Joanne » Sat Aug 02, 2008 2:10 pm

I did a three inch lap joint using a router. A lot easier than a scarf, but still probably an overkill for a tear.

Joanne
New! My Camp Cooking Forum

Project Desert Dawg website


Universal Health Care
Health care with the efficiency of the Department of Motor Vehicles
and the compassion of the Internal Revenue Service.
User avatar
Joanne
Queen of Cast Iron
 
Posts: 2111
Joined: Thu Jul 01, 2004 9:43 pm
Location: Las Vegas, NV
Top

Postby cracker39 » Sat Aug 02, 2008 5:06 pm

This is a topic that I just became interested in, as I got the bug to build a kayak and am going to use 4x8 1/4" plywood and the yak is 11 feee long...that means joining plywood.

I considered just but joining with a backing piece, or butt join at a frame where I can just screw down the ends together on the frame. The latter might result in a not perfect curve where they join.

As 1/4" ply is a little thin for splinig or biscuits, the better method is a scarf joint. I just tried making the angled ends by stacking some sample pieces at 3" intervals and using first my 3 1/2" power hand planer, then belt sander to get the angles to join. The drawing below is how the technique works if you haven't seen it done. The angled ends are supposed to be feathered down to a perfect edge, but mine were not so perfect, still with some tiny width to the edge. I drew how it is supposed to look and how mine looks. I'd have to do some filling with bondo after the piece is on the boat and curved to fit the frame. It will have fiber glass mat and resin over it anyway.

I glued two pieces together and tomorrow, I'll see how strong they are. It it looks OK, I'll try it with the plywood sides. I think I'll just butt join the bottom as there isn't as much curve to it and making the angled cuts are tedious.

Image
Dale

Sometimes I pretend to be normal. But, that gets boring...so I go back to being me.

Squidget Pop Top Build Pages http://www.thesquidget.com/ptbuild/ptbuild.html

Squidget and Pop Top Plans Info and Photos: http://www.TheSquidget.com
User avatar
cracker39
3000 Club
3000 Club
 
Posts: 3069
Images: 233
Joined: Thu Jun 30, 2005 2:18 pm
Location: Lake Alfred, Florida, USA
Top

Postby cracker39 » Sun Aug 03, 2008 11:29 am

Today, after more than 12 hours drying, I tested the joint and it seems very strong. I guess I'll use this scarf joint on my 'yak sides and butt join the bottom at a frame.
Dale

Sometimes I pretend to be normal. But, that gets boring...so I go back to being me.

Squidget Pop Top Build Pages http://www.thesquidget.com/ptbuild/ptbuild.html

Squidget and Pop Top Plans Info and Photos: http://www.TheSquidget.com
User avatar
cracker39
3000 Club
3000 Club
 
Posts: 3069
Images: 233
Joined: Thu Jun 30, 2005 2:18 pm
Location: Lake Alfred, Florida, USA
Top

Postby Juneaudave » Sun Aug 03, 2008 12:22 pm

Here is a pretty good method...I personally use a scarfing jig...

Oneoceankayaks

:thumbsup:
User avatar
Juneaudave
Super Duper Lifetime Member
 
Posts: 3237
Images: 380
Joined: Sun Jul 03, 2005 12:11 pm
Location: Juneau, Alaska
Top


Return to Teardrop Construction Tips & Techniques

Who is online

Users browsing this forum: No registered users and 9 guests