M116A3 Build

...ask your questions in the appropriate forums BUT document your build here...preferably in a single thread...dates for updates, are appreciated....

Re: M116A3 Build

Postby lfhoward » Mon Jul 27, 2020 11:17 pm

Thanks Tony, your write up and the adapter part number are super helpful.
It’s definitely a HS1600. The orange ones I’ve seen online are called a 1600 Compact.

Can you let me know if this sounds right?

So, to use the heater, I’m going to need (Starting at the heater):
- the British to American thread adapter (for 1/4”) from McMaster Carr
- propane-spec Teflon tape
- a 90° elbow to point down towards the floor
- a section of 1/4” copper tube/pipe to go through the floor, & rubber grommet for the hole, & flare fittings
- a short propane hose
- a 2-stage regulator
- and last, the propane tank for my trailer

To just test my heater out, I’ll need, at minimum:
heater):
- the British to American thread adapter (for 1/4”) from McMaster Carr
- propane-spec Teflon tape
- a short propane hose
- a 2-stage regulator
- the propane tank for my bbq grill
My off-road camper build on an M116A3 military chassis:
http://www.tnttt.com/viewtopic.php?f=50&t=62581
Tow vehicle: 2008 Jeep Liberty with a 4 inch lift.
User avatar
lfhoward
1000 Club
1000 Club
 
Posts: 1369
Joined: Wed Jan 22, 2014 6:10 pm
Location: Philadelphia, PA

Re: M116A3 Build

Postby KCStudly » Wed Jul 29, 2020 9:28 am

I'm no expert when it comes to gas lines, but my experience with copper (and aluminum) hard lines (even annealed) is that they don't take double flares well. They tend to crack at the folded edge.

Maybe someone else with more experience than me will back me up on this, but I think you will be doing single flares. :thinking:
KC
My Build: The Poet Creek Express Hybrid Foamie

Poet Creek Or Bust
Engineering the TLAR way - "That Looks About Right"
TnTTT ORIGINAL 200A LANTERN CLUB = "The 200A Gang"
Green Lantern Corpsmen
User avatar
KCStudly
Donating Member
 
Posts: 9609
Images: 8169
Joined: Mon Feb 06, 2012 10:18 pm
Location: Southeastern CT, USA

Re: M116A3 Build

Postby tony.latham » Wed Jul 29, 2020 3:31 pm

a section of 1/4” copper tube/pipe to go through the floor, & rubber grommet for the hole, & flare fittings


After the British/U.S. adapter, I went with steel pipe to get through the floor. I put another elbow underneath to connect the feeder line from the propane tank which is rubber. I sealed the hole for the pipe with epoxy and after it was cured, I installed the pipe and sealed the gap with Lexel sealant.

Image

Yes, you need a two-stage 11 WCF regulator at your propane bottle. Mine's on my tongue box:

Image

I had to use two regulators (and two lines) since my cook stove uses 27 PSI.

Other than that, I think you've got it figured out. :thumbsup:

We used ours a lot more than I thought we would. They are really nice heaters. :beer:

Tony
User avatar
tony.latham
Gold Donating Member
 
Posts: 6880
Images: 17
Joined: Mon Jul 08, 2013 4:03 pm
Location: Middle of Idaho on the edge of nowhere
Top

Re: M116A3 Build

Postby featherliteCT1 » Wed Jul 29, 2020 6:29 pm

Tony,

What did you mean by "I sealed the hole for the pipe with epoxy and after it was cured, I installed the pipe"?
Thanks
featherliteCT1
1000 Club
1000 Club
 
Posts: 1120
Joined: Wed Dec 28, 2016 6:54 am
Location: Southern Indiana
Top

Re: M116A3 Build

Postby tony.latham » Wed Jul 29, 2020 7:39 pm

featherliteCT1 wrote:Tony,

What did you mean by "I sealed the hole for the pipe with epoxy and after it was cured, I installed the pipe"?
Thanks
After I drilled the hole, I sealed the edges of plywood with epoxy to ensure everything was waterproof.

After the propane line was installed I sealed the gap with Lexen to keep the dust out of the galley.

Capish?

Tony
User avatar
tony.latham
Gold Donating Member
 
Posts: 6880
Images: 17
Joined: Mon Jul 08, 2013 4:03 pm
Location: Middle of Idaho on the edge of nowhere
Top

Re: M116A3 Build

Postby lfhoward » Thu Jul 30, 2020 2:34 pm

Thanks Tony, KC, and Featherlite. This is all good information. For the sections of pipe you did have to make, did you need to flare anything or was it all threaded connections? I think it’s a good idea to have a rubber line from the elbow below the heater over to the regulator on the tank. On my trailer this will only be a few feet.
My off-road camper build on an M116A3 military chassis:
http://www.tnttt.com/viewtopic.php?f=50&t=62581
Tow vehicle: 2008 Jeep Liberty with a 4 inch lift.
User avatar
lfhoward
1000 Club
1000 Club
 
Posts: 1369
Joined: Wed Jan 22, 2014 6:10 pm
Location: Philadelphia, PA
Top

Re: M116A3 Build

Postby lfhoward » Thu Jul 30, 2020 2:38 pm

One other curiosity I have is whether it’s possible to get an adjustable regulator. I ordered my HS1600 from across the pond in England, and over there the standard pressure is 14 WC instead of 11 WC like it is here. (US spec units have a different size propane jet.) Thus, the propane flow on my UK spec unit might be a hair slower with a US regulator. I don’t know if it will make a big difference. Thoughts?
My off-road camper build on an M116A3 military chassis:
http://www.tnttt.com/viewtopic.php?f=50&t=62581
Tow vehicle: 2008 Jeep Liberty with a 4 inch lift.
User avatar
lfhoward
1000 Club
1000 Club
 
Posts: 1369
Joined: Wed Jan 22, 2014 6:10 pm
Location: Philadelphia, PA
Top

Re: M116A3 Build

Postby tony.latham » Thu Jul 30, 2020 3:24 pm

I can’t think of the name of the U. S. distributor but I’d give them a call.

It used to be Westy Ventures and they were always responsive.

Tony
User avatar
tony.latham
Gold Donating Member
 
Posts: 6880
Images: 17
Joined: Mon Jul 08, 2013 4:03 pm
Location: Middle of Idaho on the edge of nowhere
Top

Re: M116A3 Build

Postby lfhoward » Thu Jul 30, 2020 6:39 pm

tony.latham wrote:I can’t think of the name of the U. S. distributor but I’d give them a call.

It used to be Westy Ventures and they were always responsive.

Tony

I think maybe it’s VanCafe now. They have a good lineup of Propex stuff on their website at least.
My off-road camper build on an M116A3 military chassis:
http://www.tnttt.com/viewtopic.php?f=50&t=62581
Tow vehicle: 2008 Jeep Liberty with a 4 inch lift.
User avatar
lfhoward
1000 Club
1000 Club
 
Posts: 1369
Joined: Wed Jan 22, 2014 6:10 pm
Location: Philadelphia, PA
Top

Re: M116A3 Build

Postby lfhoward » Mon Aug 03, 2020 7:16 pm

I am having a bit of an issue with the door seal that I installed the other day. The front and top aluminum sills need to be repositioned to make a good seal with the door. That’s a job for another day!
Image

With hurricane/tropical storm Isaias coming within a couple of hours, I wanted to do something to protect that seal. Well, wouldn’t you know, my new drip caps came in the mail right on time!

Holes measured and drilled.
Image

Drip cap installed with Sikaflex and screws.
Image

I factored in enough room so the door will open.
Image

In the above pictures you’ll see I have been using a piece of 2x4 to protect the door from the fender.
Image

I solved that problem with these stainless cable door catches.
Image

Image

Ready for some rain!
Image

I will need to repair the aluminum flashing around the door to get a perfect seal before driving in the rain, but while stationary these drip caps should keep the seam dry!
My off-road camper build on an M116A3 military chassis:
http://www.tnttt.com/viewtopic.php?f=50&t=62581
Tow vehicle: 2008 Jeep Liberty with a 4 inch lift.
User avatar
lfhoward
1000 Club
1000 Club
 
Posts: 1369
Joined: Wed Jan 22, 2014 6:10 pm
Location: Philadelphia, PA
Top

Re: M116A3 Build

Postby featherliteCT1 » Mon Aug 03, 2020 8:14 pm

Very creative! :thumbsup:
featherliteCT1
1000 Club
1000 Club
 
Posts: 1120
Joined: Wed Dec 28, 2016 6:54 am
Location: Southern Indiana
Top

Re: M116A3 Build

Postby lfhoward » Wed Aug 05, 2020 6:16 pm

Time to permanently take care of that leak.
Image

This upper front corner was the problem area. You can see the gap.
Image

Ripping out newly installed aluminum trim that is well Sikaflexed will destroy the trim! Luckily I had extra.
Image

The trick was to reposition the trim about 2mm outboard of the trailer side to make a better seal with the door.
Image

Speeding up the drying process. I can’t close the door until the Sikaflex cures.
Image

Now there is no gap where the door closes against the front trim. Hopefully this holds up when driving in the rain!
Image

One final touch... I put the plastic inserts into my edge trim and shaved off the blobs of sealant.

From this:
Image

To this:
Image

Ready to go camping on Friday!
Image
My off-road camper build on an M116A3 military chassis:
http://www.tnttt.com/viewtopic.php?f=50&t=62581
Tow vehicle: 2008 Jeep Liberty with a 4 inch lift.
User avatar
lfhoward
1000 Club
1000 Club
 
Posts: 1369
Joined: Wed Jan 22, 2014 6:10 pm
Location: Philadelphia, PA
Top

Re: M116A3 Build

Postby lfhoward » Fri Aug 07, 2020 8:12 pm

Made it through quite a thunderstorm with the trailer on the PA Turnpike today. At times the rain was so hard that traffic slowed to 25 mph.

The side door was waterproof!!! I win.

8)
My off-road camper build on an M116A3 military chassis:
http://www.tnttt.com/viewtopic.php?f=50&t=62581
Tow vehicle: 2008 Jeep Liberty with a 4 inch lift.
User avatar
lfhoward
1000 Club
1000 Club
 
Posts: 1369
Joined: Wed Jan 22, 2014 6:10 pm
Location: Philadelphia, PA
Top

Re: M116A3 Build

Postby featherliteCT1 » Sun Aug 09, 2020 12:49 pm

Excellent! :applause:
featherliteCT1
1000 Club
1000 Club
 
Posts: 1120
Joined: Wed Dec 28, 2016 6:54 am
Location: Southern Indiana
Top

Re: M116A3 Build

Postby lfhoward » Mon Aug 10, 2020 7:00 am

featherliteCT1 wrote:Excellent! :applause:

Thanks!!!

The trailer pulled great and camping was a wonderful time. It was our first time getting out this summer, because of a combination of Covid risk and other health issues. We circumvented having to use the campground facilities by setting up a Kelty Blockhouse “privacy shelter” with a Luggable Loo and a Nemo shower bag. Worked great!!

I noticed that the Sikaflex along the bottom of the aluminum skins where it meets the military trailer is starting to get old and fail. Some Gorilla Tape fixed that issue temporarily so that we didn’t get any water ingress while driving in the rain. Looks like I have some waterproofing maintenance to do before too long. This seems to be par for the course every few years. (Separate thread on this issue in the “Skinning Secrets” section: http://www.tnttt.com/viewtopic.php?f=65&t=72959)
My off-road camper build on an M116A3 military chassis:
http://www.tnttt.com/viewtopic.php?f=50&t=62581
Tow vehicle: 2008 Jeep Liberty with a 4 inch lift.
User avatar
lfhoward
1000 Club
1000 Club
 
Posts: 1369
Joined: Wed Jan 22, 2014 6:10 pm
Location: Philadelphia, PA
Top

PreviousNext

Return to Build Journals

Who is online

Users browsing this forum: Bing [Bot] and 13 guests