Cutting Plexi-glass w/o Splintering It

Anything to do with mechanical, construction etc

Cutting Plexi-glass w/o Splintering It

Postby Todah Tear » Tue Jun 13, 2006 9:48 am

Help!
Does anyone know of a way to cut plexi-glass with out splintering it. Is there a special blade that can be used on a jig saw to cut it.

I have tried heating the blade of a knife; that works, but not fast enough and can be ineffective because the p-g joins back together once the blade passes through. :?

Thanks,

Todah
"It is not good to have zeal without knowledge, nor to be hasty and miss the way." Proverbs 19:2 Image
User avatar
Todah Tear
Platinum Donating Member
 
Posts: 1723
Images: 282
Joined: Mon Feb 13, 2006 3:30 pm
Location: Texas

Postby Ira » Tue Jun 13, 2006 9:57 am

I don't get it--isn't Plexiglass just like Lexan, or is it really different?

I had no problem with my lexan using a fine jig saw blade.

Maybe some 3-in-one oil?
Here we go again!
User avatar
Ira
Forum Storyteller
 
Posts: 5652
Images: 118
Joined: Tue Nov 29, 2005 2:16 pm
Location: South Florida

Postby Arne » Tue Jun 13, 2006 10:04 am

first, tape it.... second, use a very fine tooth blade... I just cut a hole in my cylcle windshield with using a dremel with a minature saw blade..

I've cut down about a 1/2 dozen cycle windshields after taping using a jig saw with a fine toothed blade... similar to a hacksaw blade.
www.freewebs.com/aero-1
---
.
I hope I never get too old to play (Arne, Sept 11, 2010)
.
User avatar
Arne
Mr. Subject Line
 
Posts: 5383
Images: 96
Joined: Fri Aug 13, 2004 12:25 pm
Location: Middletown, CT
Top

Postby dwgriff1 » Tue Jun 13, 2006 10:19 am

I've always used a table saw, cutting before I removed the paper.

A sharp fairly fine tooth blade would be my prefernce, but I might use a fine, fairly dull blade. Push real gently.

In frame shops, they cut 1/8" plexi with a scoring tool, similar to a score awl used in Laminate work. They score a couple of times and pop it. It would probably work with thicker material, but I'd sure score both sides.


dave
User avatar
dwgriff1
500 Club
 
Posts: 947
Images: 4
Joined: Mon Jul 04, 2005 4:20 pm
Location: SW Idaho
Top

Postby angib » Tue Jun 13, 2006 11:23 am

Same as above - put tape where the cut will go, use a fine-tooth blade, push very gently, switch off the pendulum action if using a jigsaw.

But then I'd add - hold the workpiece down - for example, lay a piece of thick plywood over it near the cut and clamp it down. My experience is that the edge chips and cracks when the plexi isn't supported and is free to move around.

If you want to go bananas with it, clamp the plexi between two sheets of old ply and cut the whole lot.

Andrew
User avatar
angib
5000 Club
5000 Club
 
Posts: 5783
Images: 231
Joined: Fri Apr 30, 2004 2:04 pm
Location: (Olde) England
Top

Postby 48Rob » Tue Jun 13, 2006 11:31 am

Plexi-glass is much more prone to cracking than Lexan...
:thumbdown:
Rob
Waiting for "someday" will leave you on your deathbed wondering why you didn't just rearrange your priorities and enjoy the time you had, instead of waiting for a "better" time to come along...
User avatar
48Rob
Super Lifetime Member
 
Posts: 3882
Images: 4
Joined: Thu Nov 17, 2005 6:47 pm
Location: Central Illinois
Top

Postby Ira » Tue Jun 13, 2006 11:50 am

48Rob wrote:Plexi-glass is much more prone to cracking than Lexan...
:thumbdown:
Rob


That answers my question. Don't know if it comes in different thicknesses, but the Lexan I used off the shelf from HD was real thin.
Here we go again!
User avatar
Ira
Forum Storyteller
 
Posts: 5652
Images: 118
Joined: Tue Nov 29, 2005 2:16 pm
Location: South Florida
Top

Postby Chris C » Tue Jun 13, 2006 11:57 am

Okay, here's one where I KNOW I know the answer!!!!! 8) :lol:

I used to own a plastic manufacturing plant and we always used the smallest diameter blade we had.............usually 8", on a table saw. Back then all we had available was a standard plywood blade. It would cut smooth but you had to listen to the blade. The biggest problem with acrylic (Plexiglas is a trade name) is burning. So a large blade with burn. To lower the tooth speed, decrease the diameter of the blade and have fewer teeth. Today I find that a carbide blade meant for a builder's saw (circular saw) does a really good job because not only is it small in diameter, but has fewer teeth.......thus less heat.
Chris :D

The tension between what is good enough and what is beyond that creates the space for character to become our work.

Teardrop Trailer Build Pictures: http://tinyurl.com/px5cd
Chris C
.
 
Posts: 3302
Joined: Sun May 15, 2005 7:24 pm
Location: Norman, Oklahoma
Top

Postby asianflava » Tue Jun 13, 2006 2:35 pm

How thick is it? If it is thin stuff, 1/8in or 1/16in you can score it and break it. If this is lexan, forget about it. If you need to cut curves, I was told that a bandsaw with the blade on backwards is the best.

After you cut it, hit the edge with a torch to clean it up. you just need to heat it up a little to get that "Flame Polish" just be careful not to catch it on fire.
User avatar
asianflava
8000 Club
8000 Club
 
Posts: 8412
Images: 45
Joined: Mon Aug 02, 2004 5:11 am
Location: CO, Longmont
Top

Postby Juneaudave » Tue Jun 13, 2006 3:07 pm

I always cut it with a bandsaw, or with a plywood blade backwards in a table saw.
User avatar
Juneaudave
Super Duper Lifetime Member
 
Posts: 3237
Images: 380
Joined: Sun Jul 03, 2005 12:11 pm
Location: Juneau, Alaska
Top

Postby Todah Tear » Tue Jun 13, 2006 4:08 pm

Wow, talk about a wealth of information. You guys are the greatest! I'm off to my local ACE hardward store.

BTW, the plexi is 1/8".

Thanks a bunch!! :applause:

Todah
"It is not good to have zeal without knowledge, nor to be hasty and miss the way." Proverbs 19:2 Image
User avatar
Todah Tear
Platinum Donating Member
 
Posts: 1723
Images: 282
Joined: Mon Feb 13, 2006 3:30 pm
Location: Texas
Top

Postby 48Rob » Tue Jun 13, 2006 6:36 pm

Hi Chris, ;)

You may well be right, having been in the business, but what I understand is that plexiglass is poly(methyl methacrylate) a thermoplastic polymer.

And Lexan is Polycarbonate.

Plexiglass tends to shatter/crack more so than Lexan.

The names are used interchangeably, rather like "restored" and "repainted".

They are similar, and look the same on the surface, but are different underneath. ;)

Lexan is softer than plexi and scratches more easily, but is stronger.
Lexan is used for bullet proof windows.

Rob, who isn't an expert, but who did study hard before choosing the material for the trailer windows.
Waiting for "someday" will leave you on your deathbed wondering why you didn't just rearrange your priorities and enjoy the time you had, instead of waiting for a "better" time to come along...
User avatar
48Rob
Super Lifetime Member
 
Posts: 3882
Images: 4
Joined: Thu Nov 17, 2005 6:47 pm
Location: Central Illinois
Top

Postby mikeschn » Tue Jun 13, 2006 6:50 pm

So how thick would the lexan have to be to make my tear bulletproof? :o

Mike...
The quality is remembered long after the price is forgotten, so build your teardrop with the best materials...
User avatar
mikeschn
Site Admin
 
Posts: 19202
Images: 479
Joined: Tue Apr 13, 2004 11:01 am
Location: MI
Top

Postby PaulC » Tue Jun 13, 2006 7:58 pm

mikeschn wrote:So how thick would the lexan have to be to make my tear bulletproof? :o

Mike...


:lol: :lol: :applause: :rofl: :rofl2:
Time is the only real capital we have. Money you can replace but time you cannot.
User avatar
PaulC
3rd Teardrop Club
 
Posts: 4436
Images: 36
Joined: Mon May 24, 2004 7:27 am
Location: Laura, SouthernFlinders Ranges, South Australia
Top

Postby Nitetimes » Tue Jun 13, 2006 8:06 pm

mikeschn wrote:So how thick would the lexan have to be to make my tear bulletproof? :o

Mike...


Not sure but you'd need a bigger axle!! 8) 8) Much bigger
Rich


Image
ImageImage
-
The strongest reason for the people to retain the right to
keep and bear arms is, as a last resort, to protect themselves
against tyranny in government.
- Thomas Jefferson -
Personally, I carry a gun because I'm too young to die and too old to take a butt kickin'.
User avatar
Nitetimes
7000 Club
7000 Club
 
Posts: 7909
Images: 194
Joined: Sat Feb 12, 2005 12:44 am
Location: Butler,PA
Top

Next

Return to Teardrop Construction Tips & Techniques

Who is online

Users browsing this forum: No registered users and 10 guests