Is a used propane tank really cheaper?

stand up or sit down...to sink or not to sink...want or got gas...post your Q&A here..........

Is a used propane tank really cheaper?

Postby dh » Sun Jun 12, 2011 1:47 am

I found a 5lb propane tank for $5.00 at a flea market, and brought it home. I cracked the valve, and it has no pressure in it, and is rusted a bit. Where am I going with this? I am going to assume it was neglected, period. I know it needs purged, and I want it inspected before it goes back into service, and would like to re-paint it. Will this be cost efective, or would I be bettr off throwing $90.00 at new one?
Ignorant doesn't know any better, Stupid knows better but does it anyway.

My build page: http://www.tdbuildlog.blogspot.com/
User avatar
dh
Gold Donating Member
 
Posts: 1647
Joined: Fri Aug 14, 2009 7:08 pm
Location: North East Arkansas

Postby madjack » Sun Jun 12, 2011 1:59 am

...if it has a round valve handle Vs a triangular one, most refill stations won't refill it...you would have to have it inspected, tested and the valve changed out...I don't know what refurbishment would cost but what ever it cost, you would still have a used (and expensive) tank when done..............
madjack 8)
p.s. I was gonna go with one of the smaller tanks BUT because certification is only good for 5yrs, I opted to use a 20# tank and just take it in for exchange when it's certification expired............mj
...I have come to believe that, conflict resolution, through violence, is never acceptable.....................mj
User avatar
madjack
Site Admin
 
Posts: 15128
Images: 177
Joined: Thu Dec 02, 2004 5:27 pm
Location: Central Louisiana

Re: Is a used propane tank really cheaper?

Postby Dale M. » Sun Jun 12, 2011 9:59 am

dh wrote:I found a 5lb propane tank for $5.00 at a flea market, and brought it home. I cracked the valve, and it has no pressure in it, and is rusted a bit. Where am I going with this? I am going to assume it was neglected, period. I know it needs purged, and I want it inspected before it goes back into service, and would like to re-paint it. Will this be cost efective, or would I be bettr off throwing $90.00 at new one?


Costco has new 5 gallon tanks (20 lb) $29.95 ( just noticed them last week at that price).... Whoever is quoting you $90 is ripping you....

http://www.google.com/search?q=20+pound ... 0+pound+pr

Interesting price comparison....

http://www.gasgrillsnow.com/viewPrd.asp ... &ref=gbase
Vs..
http://www.ruralking.com/20-lb-type-1-p ... 3430303534

It's illegal to refill 5 gallon propane tanks that do not have OPD valve (10 -15-20-50- gallon tanks are not restricted to OPD valve)

New replacement OPD valve for old tanks are around $20 -30 ....

http://www.protanksupply.com/propane-opd-valves.asp

Propane tanks are certified for 12 years after manufacture, and must be inspected and re-certified every 6 years there after..... Check date stamp(s) on tank safety collar...

Dale
Lives his life vicariously through his own self.

Any statement made by me are strictly my own opinion.
You are free to ignore anything I say if you do not agree.

Image
User avatar
Dale M.
2000 Club
2000 Club
 
Posts: 2693
Images: 18
Joined: Thu Jun 09, 2005 8:50 pm
Location: Just a tiny bit west of Yosemite National Park
Top

Postby dh » Sun Jun 12, 2011 10:15 am

That wasn't a typo in the OP, a 5lb tank, not a 5 gallon tank. Find a MANCHESTER 5lb tank new for under $75, and I'll take it.


It doesn't need the valve changed out, and I can handle the re-paint, but how much is an inspection and purge?

The tank is dated 2006, so maybe I can just inspect for intrnal rust while I have the valve off while refurbishing tank.
Ignorant doesn't know any better, Stupid knows better but does it anyway.

My build page: http://www.tdbuildlog.blogspot.com/
User avatar
dh
Gold Donating Member
 
Posts: 1647
Joined: Fri Aug 14, 2009 7:08 pm
Location: North East Arkansas
Top

Postby Larry C » Sun Jun 12, 2011 5:47 pm

dh wrote:That wasn't a typo in the OP, a 5lb tank, not a 5 gallon tank. Find a MANCHESTER 5lb tank new for under $75, and I'll take it.


It doesn't need the valve changed out, and I can handle the re-paint, but how much is an inspection and purge?

The tank is dated 2006, so maybe I can just inspect for intrnal rust while I have the valve off while refurbishing tank.


dh,
I have a Manchester 5# bottle that has the old valve. It is in NEW condition, only been filled a couple of times and stored in a clean dry location (no rust) but it's mfg date is 1994 even though I bought it "new" in 2004. Do you know what it will actually cost to get it re certified? I can probably get the new valve and install it myself, but do you know what is involved in re certification? Does it have to be hydro tested? I can do that, but can't certify it. (at least not for a propane tank)

This 5 lb bottle is by far one of the very best camping purchases I have ever made!! It's truly a no brainer....... It's 5) 1# mini bottles at the refill price of buying just one!

Larry C
"If its worth doing it's worth doing Light"

http://www.tnttt.com/viewtopic.php?f=50&t=35852
Larry C
500 Club
 
Posts: 732
Images: 78
Joined: Sun Dec 27, 2009 9:37 am
Location: Finger Lakes
Top

Postby Dale M. » Sun Jun 12, 2011 8:15 pm

OK.... Lets do the seller is ripping you off again ( 5 lb size) .....

http://www.google.com/products/catalog? ... CG8Q8wIwAA

http://www.acehardwaresuperstore.com/pr ... /8248.html

Dale
Lives his life vicariously through his own self.

Any statement made by me are strictly my own opinion.
You are free to ignore anything I say if you do not agree.

Image
User avatar
Dale M.
2000 Club
2000 Club
 
Posts: 2693
Images: 18
Joined: Thu Jun 09, 2005 8:50 pm
Location: Just a tiny bit west of Yosemite National Park
Top

Postby dh » Mon Jun 13, 2011 12:44 am

Ok, I did a little deeper research, a reinspection is visual, no dents, dings, or pitted rust, and a soap water leak test, and thats it. The date is stamped next to the manufacture date with an ''E'' for examined. Costs from $15 to $35 (from my online research). Purging costs from $5 to $35 and is either done by filling with vapor and releasing 5 times, or by vacuum. Also, purging is required on new tanks that are not prepurged by the manufacturer.
Ignorant doesn't know any better, Stupid knows better but does it anyway.

My build page: http://www.tdbuildlog.blogspot.com/
User avatar
dh
Gold Donating Member
 
Posts: 1647
Joined: Fri Aug 14, 2009 7:08 pm
Location: North East Arkansas
Top

Postby dh » Mon Jun 13, 2011 12:58 am

Looks like I can skip the inspection, make sure it isnt rusted inside and get purged and be good to go. The $90 is for a new tank, purging, first fill, and a 'complimentary' soap test, $75 just for the tanks, which isn't that much more than Dale's prices after shipping. How much pressure can a tank take? I'd like to pressure test the valve myself before I get it filled. I can put 150lbs of air pressure on it at home.
Ignorant doesn't know any better, Stupid knows better but does it anyway.

My build page: http://www.tdbuildlog.blogspot.com/
User avatar
dh
Gold Donating Member
 
Posts: 1647
Joined: Fri Aug 14, 2009 7:08 pm
Location: North East Arkansas
Top

Postby Larry C » Mon Jun 13, 2011 6:57 am

dh wrote:Looks like I can skip the inspection, make sure it isnt rusted inside and get purged and be good to go. The $90 is for a new tank, purging, first fill, and a 'complimentary' soap test, $75 just for the tanks, which isn't that much more than Dale's prices after shipping. How much pressure can a tank take? I'd like to pressure test the valve myself before I get it filled. I can put 150lbs of air pressure on it at home.


I believe the relief valve is set at 350. If that's the case, it probably has a 5 to 1 safety factor. Burst would be above 1750. However, I may be totally wrong on this. :lol:

Larry C
"If its worth doing it's worth doing Light"

http://www.tnttt.com/viewtopic.php?f=50&t=35852
Larry C
500 Club
 
Posts: 732
Images: 78
Joined: Sun Dec 27, 2009 9:37 am
Location: Finger Lakes
Top

Postby dh » Mon Jun 13, 2011 11:24 am

I think I worded my question incorrectly. How much pressuer will it take to properly pressure test the valve? Oh, before somebody brings it up, I'd use the paint gun tap, after the filter/regulator, and before the oiler. I also use different fittings and hoses for the paint gun, so the 'paint gun' air lines never get oil in them.
Ignorant doesn't know any better, Stupid knows better but does it anyway.

My build page: http://www.tdbuildlog.blogspot.com/
User avatar
dh
Gold Donating Member
 
Posts: 1647
Joined: Fri Aug 14, 2009 7:08 pm
Location: North East Arkansas
Top

Postby Dale M. » Mon Jun 13, 2011 7:20 pm

Larry C wrote:
dh wrote:Looks like I can skip the inspection, make sure it isnt rusted inside and get purged and be good to go. The $90 is for a new tank, purging, first fill, and a 'complimentary' soap test, $75 just for the tanks, which isn't that much more than Dale's prices after shipping. How much pressure can a tank take? I'd like to pressure test the valve myself before I get it filled. I can put 150lbs of air pressure on it at home.


I believe the relief valve is set at 350. If that's the case, it probably has a 5 to 1 safety factor. Burst would be above 1750. However, I may be totally wrong on this. :lol:

Larry C


I had a propane tech at local place where they test and refit tanks tell me 260psi..

Oh well...
Lives his life vicariously through his own self.

Any statement made by me are strictly my own opinion.
You are free to ignore anything I say if you do not agree.

Image
User avatar
Dale M.
2000 Club
2000 Club
 
Posts: 2693
Images: 18
Joined: Thu Jun 09, 2005 8:50 pm
Location: Just a tiny bit west of Yosemite National Park
Top

Postby dh » Mon Jun 13, 2011 9:21 pm

Dale M. wrote:
Larry C wrote:
dh wrote:Looks like I can skip the inspection, make sure it isnt rusted inside and get purged and be good to go. The $90 is for a new tank, purging, first fill, and a 'complimentary' soap test, $75 just for the tanks, which isn't that much more than Dale's prices after shipping. How much pressure can a tank take? I'd like to pressure test the valve myself before I get it filled. I can put 150lbs of air pressure on it at home.


I believe the relief valve is set at 350. If that's the case, it probably has a 5 to 1 safety factor. Burst would be above 1750. However, I may be totally wrong on this. :lol:

Larry C


I had a propane tech at local place where they test and refit tanks tell me 260psi..

Oh well...


150 psi might not be up to spec, but still better than nothing before getting it filled.
Ignorant doesn't know any better, Stupid knows better but does it anyway.

My build page: http://www.tdbuildlog.blogspot.com/
User avatar
dh
Gold Donating Member
 
Posts: 1647
Joined: Fri Aug 14, 2009 7:08 pm
Location: North East Arkansas
Top

Postby Larry C » Tue Jun 14, 2011 6:57 am

Dale M. wrote:
Larry C wrote:
dh wrote:Looks like I can skip the inspection, make sure it isnt rusted inside and get purged and be good to go. The $90 is for a new tank, purging, first fill, and a 'complimentary' soap test, $75 just for the tanks, which isn't that much more than Dale's prices after shipping. How much pressure can a tank take? I'd like to pressure test the valve myself before I get it filled. I can put 150lbs of air pressure on it at home.


I believe the relief valve is set at 350. If that's the case, it probably has a 5 to 1 safety factor. Burst would be above 1750. However, I may be totally wrong on this. :lol:

Larry C


I had a propane tech at local place where they test and refit tanks tell me 260psi..

Oh well...


I said I might be totally wrong :cry:
Actually the tank rated pressure is stamped right on each bottle. My 5# bottle is 260, as you said, but I have and old (40 years) 20# bottle that is marked 350. I think originally they were all 350. I was told that several times over the years. My old old bottle is much heavier (empty) than the new ones (thicker).

Larry C
"If its worth doing it's worth doing Light"

http://www.tnttt.com/viewtopic.php?f=50&t=35852
Larry C
500 Club
 
Posts: 732
Images: 78
Joined: Sun Dec 27, 2009 9:37 am
Location: Finger Lakes
Top

Postby dh » Tue Jun 14, 2011 12:42 pm

I've read about this while researching the recertification process. As steel prices went up, tank wall thickness went down, as did the pressure rating.


Larry, when you hydro test a hose, how much pressure do you put on it?
Ignorant doesn't know any better, Stupid knows better but does it anyway.

My build page: http://www.tdbuildlog.blogspot.com/
User avatar
dh
Gold Donating Member
 
Posts: 1647
Joined: Fri Aug 14, 2009 7:08 pm
Location: North East Arkansas
Top

Postby Larry C » Tue Jun 14, 2011 5:03 pm

dh wrote:I've read about this while researching the recertification process. As steel prices went up, tank wall thickness went down, as did the pressure rating.


Larry, when you hydro test a hose, how much pressure do you put on it?


dh,
The hoses I work with are High Pressure which have a MWP (max working press) of 350 PSI for LPG (1 PSI for nat gas). The layline on the hose will show the MWP.

Some guidelines recommend a new hose assy. be tested at 2 times the WP (working pressure). In this case, 350PSI WP= 700PSI test pressure (proof pressure). Used hose at 1.5 times WP. For safety I do all testing in a 1/4" welded steel containment box!!

Hydrostatic testing should only be preformed by trained personnel. Also hydro testing is just a spot check to confirm the assembly meets specifications at the time of the test. However, many conditions affect the performance of a hose when it's put into service. Age, operating environment, etc. all affect the longevity of any hose. Periodic re-testing or replacement is strongly recommended.

BTW/ I wouldn't recommend using high pressure air to test your "old" bottle.

L
"If its worth doing it's worth doing Light"

http://www.tnttt.com/viewtopic.php?f=50&t=35852
Larry C
500 Club
 
Posts: 732
Images: 78
Joined: Sun Dec 27, 2009 9:37 am
Location: Finger Lakes
Top

Next

Return to Plumbing & Propane Secrets

Who is online

Users browsing this forum: No registered users and 2 guests